Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica
Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG | Alicates para Eletronica

Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG

Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG

This crimping tool can be used to crimp both male and female versions of our JST connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1" housings onto 20-28 AWG wires to make custom cables.

PTR002827
Últimas unidades em stock
50,43 €
Com IVA

Descrição

Crimping Tool: 0.08-0.5 mm² Capacity 20-28 AWG

This crimping tool can be used to crimp both male and female versions of our JST connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1" housings onto 20-28 AWG wires to make custom cables. The tool offers ratcheting action for increased consistency and ease of use.

Note: This crimping tool is narrower than our more versatile 0.1-1.0 mm² capacity crimper, and it does not crimp the full extent of the wire barrel on the JR, Futaba J, and 0.1" housing crimp pins (see the picture at the bottom of this page). It still makes a sufficient electrical connection between the crimp pin and the wire conductors, however, and the uncrimped portion of the wire barrel will be fully concealed by the connector housing.

Selecting the Right Tool

We also have a less expensive, narrower (4 mm) crimper that can also crimp JST connector, JR, Futaba J, and 0.1" housing crimp pins, though this alternate tool can only crimp the full extent of wire barrel on the JST pins. You can use the following table to help you decide which cavity of which crimping tool you need:

Tool Cavity Crimp Pins Wire Gauge (AWG)
Crimping Tool: 0.1-1.0 mm² Capacity, 16-28 AWG Outer 0.1" Housing Female
0.1" Housing Male
JST Female
JST Male
JR Female
JR Male
Futaba Female
Futaba Male
26-28
Middle 22-26
Inner Tamiya Female
Tamiya Male
Mini Tamiya Female
Mini Tamiya Male
16-20
Crimping Tool: 0.08-0.5 mm² Capacity, 20-28 AWG Outer 0.1" Housing Female
0.1" Housing Male
JST Female
JST Male
JR Female
JR Male
Futaba Female
Futaba Male
26-28
Inner 22-26

Using the Crimping Tool

Prepare the wire by stripping about 1/8" (3 mm) of insulation from the end. Place the wire in the crimp pin, lining it up so that the stripped portion lies between the inner set of tabs on the crimp pin, while insulated wire lies between the outer set of tabs.

Place the wire and crimp pin on the appropriate tooth of the tool’s die, making sure that the insulated end is on the raised and wider half of the tooth. The tabs should point toward the cavity on the other side of the die so that the tool bends them inward around the wire when it closes. 

Close the jaws of the tool slowly and completely until they release. The tabs on a properly crimped pin should form one barrel around the wire conductors and another barrel for strain relief around the wire insulation. When using this narrower crimper on the JR, Futaba J, and 0.1" housing crimp pins, only part of the wire barrel gets crimped, but it is still enough to make a sufficient electrical connection to the wire conductors, and the uncrimped portion of the wire barrel will be concealed by the crimp pin housing. This tool is wide enough to crimp the full wire barrel of the JST crimp pins.

Tip: The strain relief barrel sometimes ends up a little overly flattened, making it too wide to fit comfortably into the crimp pin housing. In such situations, you can use a pair of pliers to gently squeeze the wider axis of the barrel into a more cylindrical shape that will slide easily into the housing.

One of our customers has made a very nice video tutorial that talks about how to make custom cables with our pre-crimped wires and with self-crimped wires. The section on using our crimping tool starts at approximately 4:15 and shows the process in detail. One of our distributors has also made a short video tutorial that shows how to use our crimping tool. Both videos demonstrate how to use our wider crimping tool, but the technique is the same for this narrower crimper.

Detalhes do produtos

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies