-
ARDUINO
- RASPBERRY
- MICRO:BIT
- KITS
-
COMPONENTES
-
Resistências Elétricas
- Kit de Resistências
- Resistências 1% 125mW
- Resistencias 1% 250mW
- Resistencias 1% 500mW
- Resistencias 1% 600mW
- Resistências 1% 1W
- Resistencias 1% 2W
- Resistências 5% 125mW
- Resistencias 5% 250mW
- Resistencias 5% 500mW
- Resistências 5% 1W
- Resistencias 5% 2W
- Resistencias 5% 3W
- Resistências Potência
- Resistências Várias
- Redes Resistencias
- Termistores
- Trimmers
- Trimmers 3296
- Joysticks
- Botões
- Potenciometro slider
- Potenciometros Rotativos
- Potenciometro Multivolta
- Potenciometros Motorizados
- MODULOS
- SENSORES
- ROBÓTICA
- IMPRESSÃO 3D
-
FERRAMENTAS
Ferramenta Eletronica
- Acessórios
- Analisador Logico
- Alicates para Eletronica
- Berbequins
- Caixas Arrumação
- Chaves de Precisão
- Chaves Ajuste
- Extensões
- Fita Isoladora
- Fonte de Alimentação
- kit Ferramentas
- Lupa Eletronica
- Aparelhos de Medida, Multímetros e Outros
- Osciloscopios
- Pinças para Eletrónica
- Pontas de Prova
- Material Soldadura
- Spray de Limpeza
- Tornos e Suportes
- PROMOÇÕES
- CHEQUE PRENDA
Shield EKG EMG - Electrocardiography Electromiography
Shield EKG EMG - Electrocardiography Electromiography
This is EKG/EMG shield which allow Arduino like boards to capture Electrocardiography Electromiography signals.
Descrição
Shield EKG EMG - Electrocardiography Electromiography
This is EKG/EMG shield which allow Arduino like boards to capture Electrocardiography Electromiography signals. The shield opens new possibilities to experiment with bio feedback. You can monitor your heartbeat and log your pulse, recognize gestures by monitoring and analizyng the muscule activity as done in this project.
Features
- stackable headers up to 6 channel may be stack and wired to A0-A6 analogue inputs
- calibration signal generation by D4/D9 digital output
- preciese Trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so you should not do this unless you wat to see how things works)
- Input connector for normal or Active electrodes
- works with both 3.3V and 5V Arduino boards
DOCUMENTS
- SHIELD-EKG-EMG user's manual revision E
Hardware
- SHIELD-EKG-EMG schematic in PDF format released under Creative Commons Attribution-Share Alike 3.0 United States License
- SHIELD-EKG-EMG schematic and board in Eagle format released under Creative Commons Attribution-Share Alike 3.0 United States License
Software
- Electric guru monitoring software, created by Rob Sacks
- Arduino example for EKG capture and interface to Electric Guru for OLIMEXINO-328/Arduino boards
- Maple example for EKG capture and interface to Electric Guru for OLIMEXINO-STM32
- Pinguino example for EKG capture and interface to Electric Guru for PIC32-PINGUINO/OTG/MX220 (refer to the readme and the comments in the code for more info)
This is EKG/EMG shield which allow Arduino like boards to capture Electrocardiography Electromiography signals. The shield opens new possibilities to experiment with bio feedback. You can monitor your heartbeat and log your pulse, recognize gestures by monitoring and analizyng the muscule activity as done in this project.
FEATURESstackable headers up to 6 channel may be stack and wired to A0-A6 analogue inputscalibration signal generation by D4/D9 digital outputpreciese Trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so you should not do this unless you wat to see how things works)Input connector for normal or Active electrodesworks with both 3.3V and 5V Arduino boardsDOCUMENTSSHIELD-EKG-EMG user's manual revision EHARDWARESHIELD-EKG-EMG schematic in PDF format released under Creative Commons Attribution-Share Alike 3.0 United States LicenseSHIELD-EKG-EMG schematic and board in Eagle format released under Creative Commons Attribution-Share Alike 3.0 United States LicenseSOFTWAREElectric guru monitoring software, created by Rob SacksArduino example for EKG capture and interface to Electric Guru for OLIMEXINO-328/Arduino boardsMaple example for EKG capture and interface to Electric Guru for OLIMEXINO-STM32Pinguino example for EKG capture and interface to Electric Guru for PIC32-PINGUINO/OTG/MX220 (refer to the readme and the comments in the code for more info)