Arduino MKR WiFi 1010 | Arduino
Arduino MKR WiFi 1010 | Arduino
Arduino MKR WiFi 1010 | Arduino
Arduino MKR WiFi 1010 | Arduino
Arduino MKR WiFi 1010 | Arduino
Arduino MKR WiFi 1010 | Arduino

Arduino MKR WiFi 1010

Arduino MKR WiFi 1010

Quer adicionar WIFI aos seus dispositivos? Aqui está o MKR WIFI 1010!

Liga-se facilmente a qualquer produto Arduino utilizando software Arduino - e nem precisamos de ser peritos no assunto! Esta é a nova versão do MKR 1000 WIFI, mas com um módulo ESP32 feito pela U-BLOX.

PTR006936
Últimas unidades em stock
47,97 €
Com IVA

Descrição

Arduino MKR WiFi 1010

Description:

The MKR WIFI 1010 is a significant improvement on the MKR 1000 WIFI. It's equipped with an ESP32 module made by U-BLOX. This board aims to speed up and simplify the prototyping of WiFi based IoT applications thanks to the flexibility of the ESP32 module and its low power consumption.

The board is composed of three main blocks:

  • SAMD21 Cortex-M0+ 32bit Low Power ARM MCU;
  • U-BLOX NINA-W10 Series Low Power 2.4GHz IEEE® 802.11 b/g/n Wi-Fi; and
  • ECC508 Crypto Authentication. (datasheet)

The MKR WIFI 1010 includes 32-bit computational power, the usual rich set of I/O interfaces, and low power Wi-Fi with a Cryptochip for secure communication using SHA-256 encryption. Plus, it offers ease of use Arduino Software (IDE) for code development and programming. All of these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form.

Its USB port can be used to supply power (5V) to the board. It has a Li-Po charging circuit that allows the Arduino MKR WIFI 1010 to run on battery power or an external 5 volt source, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically.

Warning: Unlike most Arduino boards, the MKR WIFI 1010 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

Technical Specifications:

Microcontroller SAMD21 Cortex-M0+ 32bit Low Power ARM MCU
Board Power Supply (USB/VIN) 5V
Supported Battery(*) Li-Po Single Cell, 3.7V, 700mAh Minimum
Circuit Operating Voltage 3.3V
Digital I/O Pins 8
PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART 1
SPI 1
I2C 1
I2S 1
Connectivity WiFi
Analog Input Pins 7 (ADC 8/10/12 bit)
Analog Output Pins 1 (DAC 10 bit)
External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC Current per I/O Pin 7 mA
Flash Memory 256 KB
SRAM 32 KB
EEPROM No
Clock Speed 32.768 kHz (RTC), 48 MHz
LED_BUILTIN 6
Full-Speed USB Device and Embedded Host Included
LED_BUILTIN 6
Length 61.5 mm
Width 25 mm
Weight 32 gr.

Documentation:

OSH: Schematics

The MKR WiFi 1010 is open-source hardware! You can build your own board using the following files:

 EAGLE FILES IN .ZIPSCHEMATICS IN .PDF

Descrição em Português brevemente disponível!

Detalhes do produtos

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies