-
ARDUINO
- RASPBERRY
- MICRO:BIT
- KITS
-
COMPONENTES
-
Resistências Elétricas
- Kit de Resistências
- Resistências 1% 125mW
- Resistencias 1% 250mW
- Resistencias 1% 500mW
- Resistencias 1% 600mW
- Resistências 1% 1W
- Resistencias 1% 2W
- Resistências 5% 125mW
- Resistencias 5% 250mW
- Resistencias 5% 500mW
- Resistências 5% 1W
- Resistencias 5% 2W
- Resistencias 5% 3W
- Resistências Potência
- Resistências Várias
- Redes Resistencias
- Termistores
- Trimmers
- Trimmers 3296
- Joysticks
- Botões
- Potenciometro slider
- Potenciometros Rotativos
- Potenciometro Multivolta
- Potenciometros Motorizados
- MODULOS
- SENSORES
- ROBÓTICA
- IMPRESSÃO 3D
-
FERRAMENTAS
Ferramenta Eletronica
- Acessórios
- Analisador Logico
- Alicates para Eletronica
- Berbequins
- Caixas Arrumação
- Chaves de Precisão
- Chaves Ajuste
- Extensões
- Fita Isoladora
- Fonte de Alimentação
- kit Ferramentas
- Lupa Eletronica
- Aparelhos de Medida, Multímetros e Outros
- Osciloscopios
- Pinças para Eletrónica
- Pontas de Prova
- Material Soldadura
- Spray de Limpeza
- Tornos e Suportes
- PROMOÇÕES
- CHEQUE PRENDA
Português
EUR €
Módulo de Carregamento USB 2x18650 3V/5Vout
Módulo de Carregamento USB 2x18650 3V/5Vout
Módulo de Carregamento USB 2x18650 3V/5Vout
Descrição
Módulo de Carregamento USB 2x18650 3V/5Vout
Informação do fabricante:
- LED indicator(Green means full, Red means charging).
- This module is a portable mobile power supply that supports 3V / 1A and 5V / 2.2A two voltage outputs!
- This mobile power supply has a built-in lithium battery protection IC, which has overcurrent, overvoltage, undervoltage, etc.
- 5V voltage output rated current is 2.2A, maximum support 3A current (not recommended for overload, easy to damage the module, speed up the service life), the output of current depends on the quality of the 18650 battery!
- 4 level LED lights show power, the default boot is always in working state, you need to manually shut down (if necessary, change to non-working state automatic shutdown mode, just cut off the middle line of the "NC" bit or remove the"ROUT" resistor).
Attention:
- The output of current depends on the quality of the 18650 battery!
- This board cannot charge mobile phones because there is no docking agreement.
- Please charge and activate before using this board, otherwise it can not be used normally.
- The installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative! Or Installation errors will burn out the module!
- The battery voltage works normally from 3.2V to 4.2V. Do not connect the batteries in series.The voltage in series will increase.If the battery capacity needs to be increased in parallel, do not connect in series.
Instructions:
- Click to boot.
- Press and hold the button to shut down (non-automatic shutdown mode).
- If you need to change the non-automatic shutdown mode;
- please refer to the third point of the product parameters.
- Automatically turn off after 3 seconds, the battery is less than 3V alarm 6 protection.
- Less than 2.4 V full shutdown, no action.
- Battery current as low as 3uA after standby.
- Intelligent input and output, do not need to worry about long charging time.
Tips:
- During the using, please do not pull out the battery directly when the module is not turned off, otherwise the module will open the protection function, and the phenomenon that the battery cannot be turned on when the battery is installed again, at this time, the battery needs to be installed and charged to solve it.
- When you need to unplug the battery, shut down the module first and then unplug the battery(Press and hold the button to shut down).
- The installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative! Installation errors will burn out the module!
- The module has a power saving function, the indicator light will turn off after turning on for only about three seconds!
- But it is still in a state of output work.
- If you need to shut down, please manually press and hold for about two seconds until the LED light is off.