Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX
Modulo DMX-USB-RX-D8. 8 saídas digitais | Interface DMX

Modulo DMX-USB-RX-D8. 8 saídas digitais

Modulo DMX-USB-RX-D8. 8 saídas digitais

Este software para programação assenta no WIN 7 / XP / VISTA

PTR002040
Últimas unidades em stock
47,79 €
Com IVA

Descrição

Modulo DMX-USB-RX-D8. 8 saídas digitais

Informação do fabricante:

As saídas digitais podem ser aplicadas em relés, relés estado sólido, impulsos para controle de servo mecanismos ou simplesmente saídas de 0 ou 5 volts.

Descrição :

• Cumpre com o standard USITT DMX512-A, E1.11-2004 e com standard USITT DMX512/1990

• Alimentação : 9VAC ou VDC por jack ou bloco terminais com parafuso.

• Configuração fácil via USB. Nada de “dip switches”.

• Os address no modulo DMX vão do 1 ao 505

• Cada saída, no software, tem uma drop down box com 3 variáveis : Dimmer, Servo, Threshold. A saída Servo vem programada com vários tempos de “duty cicle” para os diferentes R/C servos.

• Se for escolhida uma saída Dimmer a alimentação deverá ser de 9 VAC. Não funciona com 9 VCD.

• Shunt para ligar resistência 120 Ω no DMX. Com vários módulos ligados só o ultimo modulo deve ter esta resistência ligada. Retirar todos os shunts dos módulos anteriores.

Documentos:

Informação Complementar - https://tsp.esta.org/tsp/documents/docs/ANSI-ESTA_E1-11_2008R2018.pdf

Connections
Power can be connected to the module either from an 9v AC transformer to the two pin screw terminals, or from an 9v AC or DC adapter. The module cannot be powered from the USB port. The 120 ohm terminating link connects an on-board 120 ohm resistor across the DMX. This should only be fitted to the last module on the DMX cable. Remove the link on ALL other modules. 

Getting Started
The default factory settings for your DMX-USB-RX-D8 module is DMX address 1 and all outputs set to 50% Threshold mode. 
If this is what you need, then just connect the 9V AC or DC supply, plug in the DMX cable and your away.

It's more likely that you will want to select a different DMX address or to change the operating mode. To do this you will need a PC running Windows XP/Vista/Win7.
You will need:
The DMX_D8 Configuration program.
The USB driver for windows.

Unzip the DMX_D8 Installation file into a temporary folder and click "setup" to install it.

Next install the USB driver. If your using Vista, temporarily disconnect your internet connection by unplugging the network cable or switching off the wireless connection. This is because Vista will go off and look for a suitable driver and not offer you the chance to direct it to the correct driver. It will probably install the wrong driver. Disconnecting the internet first will force it to ask you where to look. XP is fine, it asks you anyway. Connect the 9v ac or dc supply to the module, then plug in the USB cable. Windows should detect the new module and ask for the driver. Direct windows to the "inf" folder and windows will install the driver. Once installed you will have a new serial comm. port listed in Device Manager.

Run the DMX_D8 Configuration program, and you will see the following dialog. Select the new comm. port and it will find the module and display its software revision number. The DMX address the module is currently set to is displayed.

Led Status

Top Verde Led DMX Good
Middle Red Led No DMX
Bottom Blue Led USB Connected

Changing the Output Mode
Each output has its own drop down box. you can select from a variety of Dimmer/Servo and Threshold modes. If you select Dimmer mode for any output you must also supply 9VAC to the module. If you use a DC power supply, then Dimmer mode cannot work.

Servo modes provide the following pulse output ranges for a level change of 0-255:
Servo Std, 1.1mS to 1.9mS
Servo Full, 1.0mS to 2.0mS
Servo Exp1, 0.9mS to 2.1mS
Servo Exp2, 0.8mS to 2.2mS
Servo Exp3, 0.7mS to 2.3mS
The pulse is automatically repeated every 20mS.

Threshold mode with preset  thresholds from 10% to 90%

Changing the DMX address
The DMX address can be set to any between 1 and 505. Just enter the new address in the "DMX Address" edit box and click the "Update" button. The 8 channels on the DMX-USB-RX-D8 module are numbered consecutively. If you select address 505, then channel Chn1 will be at address 505, channel Chn2 will be at address 506 and channel Chn8 will be at address 512.

DMX Connections
The 5-pin XLR connections follow industry standard pin-out.

Use 5-pin XLR Pin number DMX512 Function
Common Reference 1 Data Link Common
Primary Data Link 2 Data 1-
3 Data 1+
Secondary Data Link
(unused by module, but connected through on XLR's)
4 Data 2-
5 Data 2+

Termination
If the module is the last one on the DMX cable, you should ensure the link is fitted on the board. This will enable the 120 ohm terminating resistor. 
Where the DMX is feeding through to other modules further down the cable, this link should be removed.

Dimensions

Detalhes do produtos

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies