Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H
Tic T825 USB Multi-Interface Stepper Motor Controller | Motor - Pontes H

Tic T825 USB Multi-Interface Stepper Motor Controller

Tic T825 USB Multi-Interface Stepper Motor Controller

Stock atualizado em tempo real e entregas em 24h-48h.

Compre com confiança!

PTR005615
Últimas unidades em stock
77,24 €
Com IVA

Descrição

Tic T825 USB Multi-Interface Stepper Motor Controller

The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8825 driver, and male headers and terminal blocks are included but not soldered.

It can operate from 8.5 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2.5 A max with sufficient additional cooling).

The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial.

They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).

Features and specifications

Open-loop speed or position control of one bipolar stepper motor

A variety of control interfaces:

USB for direct connection to a computer

TTL serial operating at 5 V for use with a microcontroller

I²C for use with a microcontroller

RC hobby servo pulses for use in an RC system

Analog voltage for use with a potentiometer or analog joystick

Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)

STEP/DIR inputs for compatibility with existing stepper motor control firmware

Acceleration and deceleration limiting

Maximum stepper speed: 50,000 steps per second

Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).

Up to six different microstep resolutions:

The Tic T825, Tic T834, and T249 support full step, half step, 1/4 step, 1/8 step, 1/16 step, and 1/32 step

The Tic T500 supports full step, half step, 1/4 step, 1/8 step

Digitally adjustable current limit

Optional safety controls to avoid unexpectedly powering the motor

Input calibration (learning) and adjustable scaling degree for analog and RC signals

5 V regulator (no external logic voltage supply needed)

Optional limit switch inputs with homing capabilities

Optional kill switch inputs

STEP/DIR outputs for controlling external stepper motor drivers

Connects to a computer through USB via a USB A to Micro-B cable (not included)

Free configuration software available for Windows, Linux, and macOS

Comprehensive user’s guide

The Tic T825 is based on the DRV8825 IC from Texas Instruments. It can operate from 8.5 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (absolute maximum is 2.5 A per phase).

It has reverse protection for motor power supplies up to 40 V.

Note: This version is sold unassembled so soldering is necessary to use it.

Tradução em Português brevemente disponível!

Detalhes do produtos

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies