Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy
Teensy 4.0 | Teensy

Teensy 4.0

Teensy 4.0

O Teensy 4.0 tem um processador ARM Cortex-M7 a 600MHz, com o chip NXP jMXRT1062, um dos microcontroladores mais rápido nos dias de hoje. 

Em reposição
45,26 €


Teensy 4.0

Informação do fabricante:

Teensy 4.0 features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and shape as Teensy 3.2, and retains compatibility with most of the pin functions on Teensy 3.2.

When running at 600 MHz, Teensy 4.0 consumes approximately 100mA current. Teensy 4.0 provides support for dynamic clock scaling. Unlike traditional microcontrollers, where changing the clock speed causes wrong baud rates and other issues, Teensy 4.0 hardware and Teensyduino's software support for Arduino timing functions are designed to allow dynamically speed changes. Serial baud rates, audio streaming sample rates, and Arduino functions like delay() and millis(), and Teensyduino's extensions like IntervalTimer and elapsedMillis, continue to work properly while the CPU changes speed. Teensy 4.0 also provides a power shut off feature. By connecting a pushbutton to the On/Off pin, the 3.3V power supply can be completely disabled by holding the button for 5 seconds, and turned back on by a brief button press. If a coin cell is connected to VBAT, Teensy 4.0's RTC also continues to keep track of date & time while the power is off. Teensy 4.0 also can also be overclocked, well beyond 600MHz!

The ARM Cortex-M7 brings many powerful CPU features to a true real-time microcontroller platform. Cortex-M7 is a dual-issue superscaler processor, meaning the M7 can execute two instructions per clock cycle, at 600MHz! Of course, executing two simultaneously depends upon the compiler ordering instructions and registers. Initial benchmarks have shown C++ code compiled by Arduino tends to achieve two instructions about 40% to 50% of the time while performing numerically intensive work using integers and pointers. Cortex-M7 is the first ARM microcontroller to use branch prediction. On M4, loops and other code which much branch take three clock cycles. With M7, after a loop has executed a few times, the branch prediction removes that overhead, allowing the branch instruction to run in only a single clock cycle.

Tightly Coupled Memory is a special feature which allows Cortex-M7 fast single cycle access to memory using a pair of 64 bit wide buses. The ITCM bus provides a 64 bit path to fetch instructions. The DTCM bus is actually a pair of 32 bit paths, allowing M7 to perform up to two separate memory accesses in the same cycle. These extremely high speed buses are separate from M7's main AXI bus, which accesses other memory and peripherals. 512K of memory can be accessed as tightly coupled memory. Teensyduino automatically allocates your Arduino sketch code into ITCM and all non-malloc memory use to the fast DTCM, unless you add extra keywords to override the optimized default. Memory not accessed on the tightly coupled buses is optimized for DMA access by peripherals. Because the bulk of M7's memory access is done on the two tightly coupled buses, powerful DMA-based peripherals have excellent access to the non-TCM memory for highly efficient I/O.

Teensy 4.0's Cortex-M7 processor includes a floating point unit (FPU) which supports both 64 bit "double" and 32 bit "float". With M4's FPU on Teensy 3.5 & 3.6, and also Atmel SAMD51 chips, only 32 bit float is hardware accelerated. Any use of double, double functions like log(), sin(), cos() means slow software implemented math. Teensy 4.0 executes all of these with FPU hardware.

Note: Please be aware that the Teensy 4.0 does not include headers and will need to be purchased separately and soldered on yourself.


ARM Cortex-M7 at 600MHz

1024K RAM (512K is tightly coupled)

2048K Flash (64K reserved for recovery & EEPROM emulation)

2 USB ports, both 480MBit/sec

3 CAN Bus (1 with CAN FD)

2 I2S Digital Audio

1 S/PDIF Digital Audio

1 SDIO (4 bit) native SD

3 SPI, all with 16 word FIFO

3 I2C, all with 4 byte FIFO

7 Serial, all with 4 byte FIFO

32 general purpose DMA channels

31 PWM pins

40 digital pins, all interrrupt capable

14 analog pins, 2 ADCs on chip

Cryptographic Acceleration

Random Number Generator

RTC for date/time

Programmable FlexIO

Pixel Processing Pipeline

Peripheral cross triggering

Power On/Off management


Datasheet (MIMXRT1062 DVL6A)

Manual (MIMXRT1062 DVL6A)

Datasheet (W25Q16JV-DTR)

Detalhes do produtos

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies