210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu
210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft | Motor DC com Engrenagens | Pololu

210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft

PTR006084
21,46 €
Com IVA

210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 210.59:1 metal gearbox.

 

210:1 Micro Metal Gearmotor HPCB 6V with Extended Motor Shaft

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 210.59:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. 

Overview

These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.

The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).

Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for micro metal gearmotors, to provide motor speed or position feedback.

With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change.

Please see the micro metal gearmotor datasheet (2MB pdf) for more information, including detailed performance graphs for each micro metal gearmotor version.

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 35 oz-in (2.5 kg-cm) for the 1000:1 gearboxes and 25 oz-in (2 kg*cm) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Gearmotor Dimensions

In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.

Dimensions of versions with carbon brushes (HPCB)

Dimensions of the Pololu micro metal gearmotors with carbon brushes (HPCB). Units are mm over [inches].

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies