Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |
Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |
Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |
Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |
Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |
Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal) | Motor DC com Engrenagens |

Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal)

PTR008160
28,23 €
Com IVA

Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal)

Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal)

 

Motor com Caixa Redutora 150:1 37Dx57L mm 24V (pinhão helicoidal)

Informação do fabricante:

Measuring 37 mm (1.46″) in diameter, these brushed DC gearmotors are the largest and most powerful we carry. They are available in a range of gear ratios from 6.3:1 to 150:1 and with 12 V or 24 V motors, and all versions are available with integrated 64 CPR quadrature encoders on the motor shafts. The 12 V and 24 V motors offer approximately the same performance at their respective nominal voltages, with the 24 V motor drawing half the current of the 12 V motor. See the 37D metal gearmotor datasheet (2MB pdf) for more information, including detailed performance graphs for each gearmotor version. You can also use our dynamically sortable 37D gearmotor comparison table to search for the version that offers the best combination of speed, torque, and current draw for your particular application. A more basic comparison table is available below.

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for continuously applied loads is 10 kg-cm (150 oz-in), and the recommended upper limit for instantaneous torque is 25 kg-cm (350 oz-in). Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

In general, these kinds of motors can run at voltages above and below the nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

This gearmotor is a powerful brushed DC motor with 150:1 metal gearbox intended for operation at 24 V. The gearbox is composed mainly of spur gears, but it features helical gears for the first stage for reduced noise and improved efficiency. These units have a 16 mm-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available with an integrated encoder.

Warning: Do not screw too far into the mounting holes as the screws can hit the gears. We recommend screwing no more than 3mm (0.12″) into the screw hole.

Documents:

Diagram

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies