RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H
RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H
RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H
RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H
RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H
RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda | Motor - Pontes H

RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O) - Por Encomenda

RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O)

The RoboClaw motor controllers from Ion Motion Control (formerly Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system.

PTR004090
Em reposição
258,73 €
Com IVA

Descrição

RoboClaw ST 2x45A Motor Controller (V5, screw terminal I/O)

The RoboClaw motor controllers from Ion Motion Control (formerly Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 45 A per channel (60 A peak) and has screw terminal I/O connections.

The RoboClaw from Ion Motion Control (formerly Orion Robotics) is an efficient, versatile, dual-channel synchronous regenerative motor controller. It can supply two brushed DC motors with 7.5 A, 15 A, 30 A, 45 A, or 60 A continuous (depending on the model) at voltages from 6 V to 34 V, and it allows for peak currents up to twice the maximum continuous rating.

The RoboClaw features dual quadrature decoding capability. A built-in PID routine can be used for closed-loop speed control, maintaining motor speeds even if the load varies, or the encoder counts and speeds can be read directly from the RoboClaw for use with an external control system. Analog feedback is also supported for closed-loop position control.

The RoboClaw has a USB interface that acts as a virtual serial (COM) port, allowing it to be controlled directly from a computer. Several other interface modes are supported by the RoboClaw as well: it can be controlled via TTL serial for use with an embedded system, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), or analog voltages for use with potentiometers or analog joysticks.

The RoboClaw 2x7A (V5), 2x15A (V5), 2x30A (V5), and 2x45A (V5) have USB Micro-B connectors; the RoboClaw 2×60A (V4) has a USB Mini-B connector (as did older USB RoboClaws).

This version, the Roboclaw ST 2x45A, has screw terminals for control I/O connections. It is also available with pin header I/O connections (2x45A).

Key Features

  • Simple bidirectional control of two brushed DC motors
  • 6 V to 34 V operating supply range
  • 7.5 A to 60 A maximum continuous current output, depending on controller model
  • Automatic current limiting reduces duty cycle when motor current is between 1× and 2× the controller’s rated current
  • Four communication or control options:
    1. USB serial interface (virtual COM port)
    2. Logic-level (TTL) serial interface for direct connection to microcontrollers or other embedded controllers
    3. Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    4. 0 V to 2 V (5 V tolerant) analog voltage interface for direct connection to potentiometers and analog joysticks
  • Dual feedback inputs for PID closed-loop control:
    • Speed control with quadrature encoders, up to 19.6 million encoder pulses per second
    • Position control with analog encoders or potentiometers
    • (Open-loop control with no feedback also available)
  • Screw terminals for quick connect/disconnect
  • Configurable via pushbutton interface
  • Regenerative braking
  • Tolerates high-speed direction changes
  • Jumper-selectable 5 V BEC
  • Battery monitoring and under-voltage cutoff protects batteries from over-discharging

Detalhes do produtos

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies