-
ARDUINO
- RASPBERRY
- MICRO:BIT
- KITS
-
COMPONENTES
-
Resistências Elétricas
- Kit de Resistências
- Resistências 1% 125mW
- Resistencias 1% 250mW
- Resistencias 1% 500mW
- Resistencias 1% 600mW
- Resistências 1% 1W
- Resistencias 1% 2W
- Resistências 5% 125mW
- Resistencias 5% 250mW
- Resistencias 5% 500mW
- Resistências 5% 1W
- Resistencias 5% 2W
- Resistencias 5% 3W
- Resistências Potência
- Resistências Várias
- Redes Resistencias
- Termistores
- Trimmers
- Trimmers 3296
- Joysticks
- Botões
- Potenciometro slider
- Potenciometros Rotativos
- Potenciometro Multivolta
- Potenciometros Motorizados
- MODULOS
- SENSORES
- ROBÓTICA
- IMPRESSÃO 3D
-
FERRAMENTAS
Ferramenta Eletronica
- Acessórios
- Analisador Logico
- Alicates para Eletronica
- Berbequins
- Caixas Arrumação
- Chaves de Precisão
- Chaves Ajuste
- Extensões
- Fita Isoladora
- Fonte de Alimentação
- kit Ferramentas
- Lupa Eletronica
- Aparelhos de Medida, Multímetros e Outros
- Osciloscopios
- Pinças para Eletrónica
- Pontas de Prova
- Material Soldadura
- Spray de Limpeza
- Tornos e Suportes
- PROMOÇÕES
- CHEQUE PRENDA
Português
EUR €
Kit DIY Módulo Gerador de Sinal de Função Monolítica - ICL8038
Kit DIY Módulo Gerador de Sinal de Função Monolítica - ICL8038
Kit DIY de módulo gerador de sinal ICL8038
Descrição
Kit DIY Módulo Gerador de Sinal de Função Monolítica - ICL8038
Informação do fabricante:
ICL8038 pin functions:
- 1 foot, 12 foot: sine waveform adjusting terminal;
- 2 foot: sine wave output;
- 3 foot: triangle wave output;
- 4 foot, 5 foot: the frequency and duty cycle (or waveform asymmetry) adjustment;
- 6 foot: V +, the positive power supply;
- 7 foot: offset; 8 foot: frequency adjustment input terminal;
- 9 foot: square wave output.
- This is an open collector output terminal, work should take a load resistor to the corresponding positive power supply terminal from the pin, to get a TTL-compatible square-wave output, the load resistance must be connected to + 5V power supply;
- 10 foot: timing capacitor terminal;
- 11 foot: V-, negative power supply terminal or the ground. Use positive and negative power supply, 11 feet to the negative supply, the output waveform are symmetrical with respect to 0V; use a single positive power supply, 11 feet grounded, the output waveform is unipolar, uniform voltage is + VCC / 2;
- 13 feet, 14 Feet: Empty foot.
- The kits are designed for a frequency range is 50-5KHz, two bands with a switch S to switch, RP1 is the frequency adjustment, RP2 is the duty cycle adjustment, RP3 is a sine wave distortion adjustment. Circuit uses 12V single power supply, input from the X1; X2, X3 is a waveform output side, you can use oscilloscope to observe three output waveforms.
- Model: ICL8038
- Input 12V DC
- Frequency range 50-5KHz,
- Size:6cmx4.5cmx0.2cm
- Weight:26g
Detalhes do produtos
Talvez goste