FiPy | WiFi |


Stock Reduzido
97,85 €


Fipy é um módulo de desenvolvimento Wifi



Note: The LTE Antenna MUST always be used with LTE CAT M1 / NB1, or it could cause serious damage to the development board.

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. FiPy includes WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board.

Get on with a board that gives you full flexibility during testing, install, deployment and even later when you want to switch real-time your airtime network provider. You can switch when the time is right for you or set some parameters that will do so automatically.

FiPy Features

Powerful CPU

Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1, LoRa and Sigfox

1KM WiFi range

MicroPython enabled

Fits in a standard breadboard (with headers)

Ultra-low power usage: a fraction compared to other connected microcontrollers


Espressif ESP32 SoC

Dual processor and WiFi radio system on chip

Networking processor handles the WiFi connectivity and the IPv6 stack

Main processor is entirely free to run the user application

An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA


2 x UART, 2 x SPI, I2C, micro SD card

ANalog channels: 8_12 bit ADCs, 2_8 bit DAC

Timers: 2_64 bit with PWM with up to 16 channels

DMA on all peripherals

GPIO: Up to 22

Hash / Encryption


WiFi Networking

802.11b/b/n 16mbps


Low energy and classic


Running at 32KHz


Node range: Up to 50km

Security & Certifications

SSL/TLS support up to 1.2

 WPA Enterprise security

AES encryption engine



Flash Memory: 8MB

GPIO: Up to 22

Hardware floating point acceleration

Python multi-threading


Voltage Input: 3.3V  5.5V

3v3 output capable of sourcing up to 400mA

Sigfox Operating Frequencies

RCZ1 – 868MHz(Europe)

RCZ2 – 902MHz (US, Canada and Mexico)

RCZ3 – (Japan and Korea)

RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia)

Sigfox Specification

Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology

Class 0 device. Maximum Tx power:

– 14dBm (Europe)

– 22dBm (America)

– 22dBm (Australia and New Zealand)

Node range: Up to 50km

Sigfox pre-certified (October 2016)


Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby

Sigfox (Australia, New Zealand and South America):

24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby

Bluetooth Networking

Low energy and classic

Compliant with Bluetooth v4.2 BR/EDR and BLE specification

Class-1, Class-2 and Class-3 transmitter without external power amplifer

Enhanced power control

10dBm transmitting power

NZIF receiver with -98 dBm sensitivity

Adaptive Frequency Hopping (AFH)

Standard HCI based on SDIO/SPI/UART

High speed UART HCI, up to 4 Mbps

BT 4.2 controller and host stack

Service Discover Protocol (SDP)

General Access Profile (GAP)

Security Manage Protocol (SMP)

Bluetooth Low Energy (BLE)



All GATT-based profile supported

SPP-Like GATT-based profile

BLE Beacon


CVSD and SBC for audio codec

Bluetooth Piconet and Scatternet

LoRa Operating Frequencies

868MHz(Europe) at 14dBm maximum

915MHz (North and South America, Australia and New Zealand) at 20dBm maximum

LoRa Specification

Power consumption: 10mA Rx, 28mA Tx

LoRaWAN stack – Class A and C devices

Node range: Up to 40km

Nano-gateway: Up to 22km (Capacity up to 100 nodes)

LTE-M Operating Frequencies

34 bands supports from 699Mhz to 2170Mhz (Total world-wide support)

– Data rates:

300 kbps DL

375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD)

40 kbps DL

55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD)

Tx/Rx Frequencies

Ports for LTE Bands

Tx frequencies

Rx frequencies

Low bands 5, 8, 12, 13, 18, 19, 20, 28

699 to 915 MHz

729 to 960 MHz

Mid bands 1, 2, 3, 4

1710 to 1980MHz

1805 to 2170 MHz

WiFi Networking

Up to 1km range

802.11b/g/n 16mbps

Power: 12mA in active mode, 5uA in standby


55m x 20mm x 3.5mm (Without Headers)



31g (Packaged)

Tradução em Português brevemente disponível!

Clientes que compraram este produto também compraram:

Produto adicionado a lista de desejos

Ao continuares a navegar estás a consentir a utilização de cookies que possibilitam a apresentação de serviços e ofertas adaptadas aos teus interesses. Poderá consultar no seguinte link a nossa Politica de Cookies