-
ARDUINO
- RASPBERRY
- MICRO:BIT
- KITS
-
COMPONENTES
-
Resistências Elétricas
- Kit de Resistências
- Resistências 1% 125mW
- Resistencias 1% 250mW
- Resistencias 1% 500mW
- Resistencias 1% 600mW
- Resistências 1% 1W
- Resistencias 1% 2W
- Resistências 5% 125mW
- Resistencias 5% 250mW
- Resistencias 5% 500mW
- Resistências 5% 1W
- Resistencias 5% 2W
- Resistencias 5% 3W
- Resistências Potência
- Resistências Várias
- Redes Resistencias
- Termistores
- Trimmers
- Trimmers 3296
- Joysticks
- Botões
- Potenciometro slider
- Potenciometros Rotativos
- Potenciometro Multivolta
- Potenciometros Motorizados
- MODULOS
- SENSORES
- ROBÓTICA
- IMPRESSÃO 3D
-
FERRAMENTAS
Ferramenta Eletronica
- Acessórios
- Analisador Logico
- Alicates para Eletronica
- Berbequins
- Caixas Arrumação
- Chaves de Precisão
- Chaves Ajuste
- Extensões
- Fita Isoladora
- Fonte de Alimentação
- kit Ferramentas
- Lupa Eletronica
- Aparelhos de Medida, Multímetros e Outros
- Osciloscopios
- Pinças para Eletrónica
- Pontas de Prova
- Material Soldadura
- Spray de Limpeza
- Tornos e Suportes
- PROMOÇÕES
- CHEQUE PRENDA
EMG30 - GearMotor with encoder
EMG30 - GearMotor with encoder
The EMG30 is a 12v motor fully equipped with encoders and a 30:1 reduction gearbox. It is ideal for small or medium robotic applications, providing cost effective drive and feedback for the user.
Descrição
EMG30 - GearMotor with encoder
The EMG30 (encoder, motor, gearbox 30:1) is a 12v motor fully equipped with encoders and a 30:1 reduction gearbox. It is ideal for small or medium robotic applications, providing cost effective drive and feedback for the user. It also includes a standard noise suppression capacitor across the motor windings.
Measurements
Connector
The EMG30 is supplied with a 6 way JST connector (part no PHR-6) at the end of approx 90mm of cable as standard.
The connections are:
Wire colour | Connection | |
Purple (1) | Hall Sensor B Vout | |
Blue (2) | Hall sensor A Vout | |
Verde (3) | Hall sensor ground | |
Brown (4) | Hall sensor Vcc | |
Red (5) | + Motor | |
Black (6) | - Motor |
Wire colours are from the actual cable.
The hall sensors accept voltages between 3.5v and 20v.
The outputs are open collector and require pull-ups to whatever signal level is required.
On the MD25 they are powered from 12v and pulled up to 5v for the signals.
Specification |
||
Rated voltage | 12v | |
Rated torque | 1.5kg/cm | |
Rated speed | 170rpm | |
Rated current | 530mA | |
No load speed | 216 | |
No load current | 150mA | |
Stall Current | 2.5A | |
Rated output | 4.22W | |
Encoder counts per output shaft turn | 360 |
Measured Shaft Speed when used off-load with MD23 and 12v supply. | ||
Minimum Speed | 1.5rpm | |
Maximum Speed | 200rpm |