-
ARDUINO
- RASPBERRY
- MICRO:BIT
- KITS
-
COMPONENTES
-
Resistências Elétricas
- Kit de Resistências
- Resistências 1% 125mW
- Resistencias 1% 250mW
- Resistencias 1% 500mW
- Resistencias 1% 600mW
- Resistências 1% 1W
- Resistencias 1% 2W
- Resistências 5% 125mW
- Resistencias 5% 250mW
- Resistencias 5% 500mW
- Resistências 5% 1W
- Resistencias 5% 2W
- Resistencias 5% 3W
- Resistências Potência
- Resistências Várias
- Redes Resistencias
- Termistores
- Trimmers
- Trimmers 3296
- Joysticks
- Botões
- Potenciometro slider
- Potenciometros Rotativos
- Potenciometro Multivolta
- Potenciometros Motorizados
- MODULOS
- SENSORES
- ROBÓTICA
- IMPRESSÃO 3D
-
FERRAMENTAS
Ferramenta Eletronica
- Acessórios
- Analisador Logico
- Alicates para Eletronica
- Berbequins
- Caixas Arrumação
- Chaves de Precisão
- Chaves Ajuste
- Extensões
- Fita Isoladora
- Fonte de Alimentação
- kit Ferramentas
- Lupa Eletronica
- Aparelhos de Medida, Multímetros e Outros
- Osciloscopios
- Pinças para Eletrónica
- Pontas de Prova
- Material Soldadura
- Spray de Limpeza
- Tornos e Suportes
- PROMOÇÕES
- CHEQUE PRENDA
Arduino Uno Wifi Rev2
Arduino Uno Wifi Rev2
Com este Arduino Uno WiFi irá poder adicionar WIFI aos seus projetos! Este é como se se tratasse de um Arduino UNO Rev3 mas com maior potência: vem com o novo processador de 8 bits da Microchip ( ATMEGA4809 ) e com um sensor inercial (IMU) integrado na placa. Relativamente à ligação WiFi, agora poderá comunicar com maior segurança devido ao novo chip de aceleração criptográfica ECC608.
Descrição
Arduino Uno Wifi Rev2
Description:
Add this board to a device and you'll be able to connect it to a WiFi network, using its secure ECC608 crypto chip accelerator.
The Arduino Uno WiFi is functionally the same as the Arduino Uno Rev3, but with the addition of WiFi and some other enhancements.
It incorporates a brand new 8-bit microprocessor from Microchip and has an onboard IMU (Inertial Measurement Unit).
The Wi-Fi Module is a self-contained SoC with integrated TCP/IP protocol stack that can provide access to a Wi-Fi network, or act as an access point.
The Arduino Uno WiFi has 14 digital input/output pins—5 can be used as PWM outputs with Pin 11 that is not PWM as on the UNO Rev3 —6 analog inputs, a USB connection, a power jack, an ICSP header, and a reset button.
It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with an AC adapter or battery to get started.
Technical Specifications:
Microcontroller | ATMEGA4809 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7 - 12V |
Input Voltage (limit) | 6 - 12V |
Digital I/O Pins | 14 — 5 Provide PWM Output |
PWM Digital I/O Pins | 5 |
Analog Input Pins | 6 |
DC Current per I/O Pin | 20 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 48 KB (ATMEGA4809) |
SRAM | 6,144 B (ATMEGA4809) |
EEPROM | 256 Bytes (ATMEGA4809) |
Clock Speed | 16 MHz |
LED_BUILTIN | 25 |
Length | 68.6 mm |
Width | 53.4 mm |
Weight | 25 g |
PLEASE NOTE: Pin 11 is not PWM enabled and the connector is wrongly marked on some batches. Available PWM pins are: 3, 5, 6, 9, and 10.
Descrição em Português brevemente disponível!